Article ID | Journal | Published Year | Pages | File Type |
---|---|---|---|---|
1313675 | Journal of Fluorine Chemistry | 2014 | 10 Pages |
•Functional fluorinated oligomer was synthesized by the short perfluoralkyl monomer.•PDMS was used as spacer introduced between epoxy resin and fluorinated segments.•Kite-like fluorosilicone copolymer was prepared by fluorinated oligomer and PDMS.•High hydrophobic surface was obtained by incorporation fluorosilicone copolymer.•The surface fluorine content of modified resin was 2.18 × 105 time than bulk content.
Two series of fluorinated siloxane star-like copolymers, with different molecular weight of siloxane segments and large fluorinated segments at the tail, were synthesized from dicarboxyl terminated poly(2,2,3,4,4,4-hexafluorobutyl acrylate) (CTHFA) and dihydroxypropyl-terminated poly(dimethyl siloxane) (PDMS). The chemical structures of the star-like copolymer (CTHFA-PDMS) were measured by FT-IR, 1H NMR, 13C NMR and GPC. Long siloxane spacers were employed to increase the migration efficiency of the large fluorinated segments. The long siloxane spacers also played a part in toughening the epoxy resin. Then, the copolymers reacted with 4′4-diphenylmethane dissocyanate and were used as a surface modifier of cured commercial diglycidyl ether of bisphenol A (DGEBA) at different concentration (0.1–0.5 wt% with respect to DGEBA). For both kinds of the CTHFA-PDMS modified DGEBA, high water contact angles (122° and 110°) were obtained at very low concentration (0.2 wt%). The surface chemical composition was measured by X-ray photoelectron spectroscopy (XPS). It was found that the fluorine and silicon atoms selectively migrated toward the outermost surface of modified DGEBA resin. The surface enrichment factors of fluorine and silicon atoms (SmF and SmSi) of modified resin were up to 2.18 × 105 and 2.93 × 104 times than the theoretical value expected for the bulk formulations at very low concentration (0.2 wt%). Moreover, the surface of modified epoxy resins showed good chemical stability by immersing in acidic and salt solutions. Scanning electron microscopy (SEM) images observed many ridges and rough crack structures of the fracture surface of modified DGEBA resin, indicating the CTHFA-PDMS toughened the DGEBA network.
Graphical abstractIn order to lower the surface energy of epoxy resin with small amount of fluorine content, long siloxane spacers were introduced between graft copolymer and fluorinated segments. A novel fluorinated siloxane graft copolymer with different molecular weight of siloxane segments, carrying long fluorinated segments at the tail synthesized from dicarboxyl terminated poly(2,2,3,4,4,4-hexafluorobutyl acrylate) (CTHFA) and dihydroxypropyl-terminated poly(dimethyl siloxane) (PDMS). Then the fluorinated siloxane graft copolymer was employed as a surface modifier of cured commercial diglycidyl ether of bisphenol A (DGEBA) at different concentration (0.1–0.5 wt% with respect to DGEBA). For both kinds of fluorinated siloxane graft copolymer modified DGEBA, high water contact angle (122° and 110°) were obtained at very low concentration (0.2 wt%). The surface chemical composition was measured by X-ray photoelectron spectroscopy (XPS). The surface enrichment factors of fluorine and silicon atoms (SmF and SmSi) of modified resin were up to 2.18 × 105 and 2.93 × 104 times than the theoretical value expected for the bulk formulations at very low concentration (0.2 wt%). The tensile strength of modified DGEBA using CTHFA-g-PDMS with high molecular weight increased to a maximum value (82.2 MPa) with increasing CTHFA-g-PDMS content scanning electron microscopy (SEM) images observed many ridges and rough crack structures of the fracture surface of graft-modified DGEBA resin, indicating the CTHFA-g-PDMS toughened the DGEBA network.Figure optionsDownload full-size imageDownload as PowerPoint slide