Sensitivity of mechatronical systems represented by polar graphs and structural numbers as models of discrete systems Fulltext Access 8 Pages 2006
Kinetics and mechanism of periodic structure formation at SiO2/Mg interface Fulltext Access 8 Pages 2006
Plastic strain distribution underneath a Vickers Indenter: Role of yield strength and work hardening exponent Fulltext Access 8 Pages 2006
Mode I crack growth rate of a ferromagnetic elastic strip in a uniform magnetic field Fulltext Access 8 Pages 2006
Glassy carbon particles as component to modification of tribological properties Fulltext Access 8 Pages 2006
Corrosive effects of salt hydrate phase change materials used with aluminium and copper Fulltext Access 8 Pages 2006
Properties of composite materials with polymer matrix reinforced with Nd–Fe–B hard magnetic particles Fulltext Access 8 Pages 2006
An intelligent system for monitoring and optimization of ball-end milling process Fulltext Access 8 Pages 2006
Coatings of metastable ceramics deposited by solution-precursor plasma spray: I. Binary ZrO2–Al2O3 system Fulltext Access 8 Pages 2006
Austenite decomposition during press hardening of a boron steel—Computer simulation and test Fulltext Access 8 Pages 2006
Analytical model for free form radii after deep and stretch drawing using pressurised membranes Fulltext Access 8 Pages 2006
Cycle time prediction in high-speed milling operations for sculptured surface finishing Fulltext Access 8 Pages 2006
Surface modification to improve friction and galling properties of forming tools Fulltext Access 8 Pages 2006
A method for stress space forming limit diagram construction for aluminum alloys Fulltext Access 8 Pages 2006
Working range for sequences and series of two-symmetrical grooves in wire rod rolling Fulltext Access 8 Pages 2006
Quantitative criterion for recrystallization nucleation in single-phase alloys: Prediction of critical strains and incubation times Fulltext Access 8 Pages 2006
Room-temperature creep of soft PZT under static electrical and compressive stress loading Fulltext Access 8 Pages 2006
Lattice-based structures for studying percolation in two-dimensional grain networks Fulltext Access 8 Pages 2006
Improvements in sintered density and dimensional stability of powder injection-molded 316L compacts by adjusting the alloying compositions Fulltext Access 8 Pages 2006
Ultrafine, perfectly spherical Ni-Zn ferrite nanoparticles, with ultranarrow distribution, isolated in a silica matrix, prepared by a novel synthesis method in the liquid phase Fulltext Access 8 Pages 2006
Phase-field simulation of sintering and related phenomena - A vacancy diffusion approach Fulltext Access 8 Pages 2006
Plastic deformation and fracture of ultrafine-grained Al-Mg alloys with a bimodal grain size distribution Fulltext Access 8 Pages 2006
Microstructural features induced by spray processing and hot extrusion of an Al-18% Si-5% Fe-1.5% Cu alloy Fulltext Access 8 Pages 2006
Leaf-like dislocation substructures and the decrease of martensitic start temperatures: A new explanation for functional fatigue during thermally induced martensitic transformations in coarse-grained Ni-rich Ti-Ni shape memory alloys Fulltext Access 8 Pages 2006
Erosion corrosion in stainless steel pipe under water vapour two-phase flow conditions Fulltext Access 8 Pages 2006
Inverse determination of temperature dependent thermal conductivity using network simulation method Fulltext Access 8 Pages 2006
A thick-interface model for diffusive and massive phase transformation in substitutional alloys Fulltext Access 8 Pages 2006
Texture transition in Cu thin films: Electron backscatter diffraction vs. X-ray diffraction Fulltext Access 8 Pages 2006
Theoretical modeling of coexisting tetragonal and rhombohedral heterophase polydomain structures in lead zirconate titanate ferroelectric films near the morphotropic phase boundary Fulltext Access 8 Pages 2006
Near-coincidence-sites modeling of the edge facet dislocation structures of α precipitates in a Ti–7.26 wt.% Cr alloy Fulltext Access 8 Pages 2006
Failure mechanisms of closed-cell aluminum foam under monotonic and cyclic loading Fulltext Access 8 Pages 2006
Experimental verification of ribbon formation process in chill-block melt spinning Fulltext Access 8 Pages 2006
Multiscale modeling of materials by a multifield approach: Microscopic stress and strain distribution in fiber–matrix composites Fulltext Access 8 Pages 2006
Detailed assessment of indentation size-effect in recrystallized and highly deformed niobium Fulltext Access 8 Pages 2006
Coatings of metastable ceramics deposited by solution-precursor plasma spray: II. Ternary ZrO2–Y2O3–Al2O3 system Fulltext Access 8 Pages 2006
Automation of the processes of surface measurement and of deposition by welding for the recovery of rotors of large-scale hydraulic turbines Fulltext Access 8 Pages 2006
Analytical modeling of heat conduction for small scale resistance spot welding process Fulltext Access 8 Pages 2006
A new procedure using the microhardness technique for sheet material damage characterisation Fulltext Access 8 Pages 2006
Effect of martensite volume fraction and its morphology on the tensile properties of ferritic ductile iron with dual matrix structures Fulltext Access 8 Pages 2006
Simple shear tests: Experimental techniques and characterization of the plastic anisotropy of rolled sheets at large strains Fulltext Access 8 Pages 2006
Laser cutting of steel sheets: Influence of workpiece thickness and beam waist position on kerf size and stria formation Fulltext Access 8 Pages 2006
The effect of processing and Mn content on the T5 and T6 properties of AA6082 profiles Fulltext Access 8 Pages 2006
Candidature of equal channel angular pressing for processing of tubular commercial purity-titanium Fulltext Access 8 Pages 2006
Hard turning of tempered DIN 100Cr6 steel with coated and no coated CBN inserts Fulltext Access 8 Pages 2006
A simple experimental tooling with internal pressure source used for evaluation of material formability in tube hydroforming Fulltext Access 8 Pages 2006
FEM optimization of tool geometry based on the machined near surface's residual stresses generated in diamond turning Fulltext Access 8 Pages 2006
Effect of welding parameters on mechanical and microstructural properties of AA6056 joints produced by Friction Stir Welding Fulltext Access 8 Pages 2006
Rigid-plastic finite element analysis of plastic deformation of porous metal sheets containing internal void defects Fulltext Access 8 Pages 2006
Investigation of lubrication effect on the backward extrusion of thin-walled rectangular aluminum case with large aspect ratio Fulltext Access 8 Pages 2006
Modelling and experimental analysis of the effects of tool wear on form errors in stainless steel blanking Fulltext Access 8 Pages 2006
Development of a micro-punching machine and study on the influence of vibration machining in micro-EDM Fulltext Access 8 Pages 2006
In-process evaluation of grit protrusion feature for fine diamond grinding wheel by means of electro-contact discharge dressing Fulltext Access 8 Pages 2006
A finite element simulation of the spherical mandrelling process of holes with cracks Fulltext Access 8 Pages 2006
Effect of shielding conditions of local dry cavity on weld quality in underwater Nd:YAG laser welding Fulltext Access 8 Pages 2006
Analysis of deformation behavior in 3D during equal channel angular extrusion Fulltext Access 8 Pages 2006
Studies on rheology of ceramic inks and spread of ink droplets for direct ceramic ink jet printing Fulltext Access 8 Pages 2006
A contribution to a qualitative understanding of thermo-mechanical effects during chip formation in hard turning Fulltext Access 8 Pages 2006
An investigation of lapping characteristics for improving the form error of an aspheric lens Fulltext Access 8 Pages 2006
Spheroidization of metal and ceramic powders in thermal plasma jet: Comparison between experimental results and theoretical estimation Fulltext Access 8 Pages 2006
New short time face turning method for testing the machinability of PM steels Fulltext Access 8 Pages 2006
Reduction of the heat treatment process for Al-based alloys by utilization of heat from the solidification process Fulltext Access 8 Pages 2006
Evolution of microstructure and strengthening of 7050 Al alloy by ECAP combined with heat-treatment Fulltext Access 8 Pages 2006
Simulation studies of process flow with in-line part inspection in machining cells Fulltext Access 8 Pages 2006
Finite element investigation of equal channel angular extrusion with back pressure Fulltext Access 8 Pages 2006
Physical property and electrical conductivity of electroless Ag-plated carbon fiber-reinforced paper Fulltext Access 8 Pages 2006
Tool wear detection in turning operations using singular spectrum analysis Fulltext Access 8 Pages 2006
Prediction of spring-back behavior in high strength low carbon steel sheets Fulltext Access 8 Pages 2006
Mould flow and component design analysis of polymeric based composite automotive clutch pedals Fulltext Access 8 Pages 2006
Modeling of virtual workpiece with machining errors representation in turning Fulltext Access 8 Pages 2006
Residual stresses in turning: Part II. Influence of the machined material Fulltext Access 8 Pages 2006
Use of micromechanical modelling in the material characterisation of overinjected thermoplastic composites Fulltext Access 8 Pages 2006
Design of genetic-fuzzy expert system for predicting surface finish in ultra-precision diamond turning of metal matrix composite Fulltext Access 8 Pages 2006
Constitutive model of the alloy 2117-T4 at low strain rates and temperatures Fulltext Access 8 Pages 2006
Novel applications of smoothed particle hydrodynamics (SPH) in metal forming Fulltext Access 8 Pages 2006
Simulation of the gas-assisted injection molding process using a mid-plane model of a contained-channel part Fulltext Access 8 Pages 2006