Microscopic thermodynamic basis of normality structure of inelastic constitutive relations Fulltext Access 7 Pages 2005
Grain refinement, thermal stability and tensile properties of 2024 aluminum alloy after equal-channel angular pressing Fulltext Access 7 Pages 2005
Laser cutting of different polymeric plastics (PE, PP and PC) by a CO2 laser beam Fulltext Access 7 Pages 2005
Effects of degrees of deformation and stress-relief temperatures on the mechanical properties and residual stresses of cold drawn mild steel rods Fulltext Access 7 Pages 2005
Titanium nitride layer formation by TIG surface melting in a reactive environment Fulltext Access 7 Pages 2005
Wear and surface roughness of current veneered materials after toothbrush/dentifrice abrasion Fulltext Access 7 Pages 2005
A photo-plastic experimental study on deformation of rotary forging a ring workpiece Fulltext Access 7 Pages 2005
Fabrication of pure Al/Mg-Li alloy clad plate and its mechanical properties Fulltext Access 7 Pages 2005
Effect of copper and silicon content on mechanical properties in Al-Cu-Si-Mg alloys Fulltext Access 7 Pages 2005
Orientation of short fibers in powder injection molded aluminum matrix composites Fulltext Access 7 Pages 2005
Improvement of mechanical properties for Zn-Al alloys using equal-channel angular pressing Fulltext Access 7 Pages 2005
Use of artificial neural networks to predict the deformation behavior of Zr-2.5Nb-0.5Cu Fulltext Access 7 Pages 2005
Development of the sheared edge in the trimming of steel and light metal sheet Fulltext Access 7 Pages 2005
Fabrication of metal matrix composites by a high-pressure centrifugal infiltration process Fulltext Access 7 Pages 2005
Joining of titanium/stainless steel by explosive welding and effect on interface Fulltext Access 7 Pages 2005
Simulation of edge dislocation emission from a crack under in-plane shear Fulltext Access 7 Pages 2005
Material force for dynamic crack propagation in multiphase micromorphic materials Fulltext Access 7 Pages 2005
Quantitative reliability analysis of different design alternatives for steer-by-wire system Fulltext Access 7 Pages 2005
Evolutionary neural network modeling for software cumulative failure time prediction Fulltext Access 7 Pages 2005
Weighing the world's heaviest telescope at eight points with corrections for lifting perturbations Fulltext Access 7 Pages 2005
Finite element analysis on global and local estimation for thermo-mechanical response of EPL wafer heating Fulltext Access 7 Pages 2005
High-efficiency finishing process for metal mold by large-area electron beam irradiation Fulltext Access 7 Pages 2005
Electro-magnetically enforced rotary barrel finishing for fabricating spherically contoured quartz crystal blanks Fulltext Access 7 Pages 2005
Development of measures to estimate truncation error in fault tree analysis Fulltext Access 7 Pages 2005
A response surface method based on weighted regression for structural reliability analysis Fulltext Access 7 Pages 2005
Dimensionless design graphs for flexure elements and a comparison between three flexure elements Fulltext Access 7 Pages 2005
Crack propagation in an orthotropic medium with coupled elastodynamic properties Fulltext Access 7 Pages 2005
Strain fields caused by doughnut-like and tubular inclusions with uniform eigenstrains Fulltext Access 7 Pages 2005
(Bejan's) early vs. late regimes method applied to entropy generation in one-dimensional conduction Fulltext Access 7 Pages 2005
Temporal correlation modification by microbubbles injection in a channel flow Fulltext Access 7 Pages 2005
Simulation of heat transfer on an oscillatory blood flow in an indented porous artery Fulltext Access 7 Pages 2005
Numerical model of internal heat source capacity in desorption step of ETSA process Fulltext Access 7 Pages 2005
First-order differential sensitivity analysis of a nuclear safety system by Monte Carlo simulation Fulltext Access 7 Pages 2005
Study of transient forced convection heat transfer from discrete heat sources in a FC-72 cooled vertical channel Fulltext Access 7 Pages 2005
On the fluid flow in the anterior chamber of a human eye with slip velocity Fulltext Access 7 Pages 2005
On the thermal performance of an internally finned three-dimensional cubic enclosure in natural convection Fulltext Access 7 Pages 2005
Identification of the upward gas flow velocity and of the geometric characteristics of a flame with a specific thermal sensor Fulltext Access 7 Pages 2005
Radiative characteristics of beds made of large spheres containing an absorbing and scattering medium Fulltext Access 7 Pages 2005
Friction drag resulting from the simultaneous imposed motions of a freestream and its bounding surface Fulltext Access 7 Pages 2005
A computational study of natural convection in a liquid-encapsulated molten semiconductor with a horizontal magnetic field Fulltext Access 7 Pages 2005
Film condensations of flowing mixtures of steam and air on an inclined flat plate Fulltext Access 7 Pages 2005
Note on the mechanism of interfacial mass transfer of absorption processes Fulltext Access 7 Pages 2005
Orthotropic effect and strain dependency of paperboard on load characteristic of center bevel cutter indented on paperboard Fulltext Access 7 Pages 2005
Dimensional accuracy studies of copper shells used for electro-discharge machining electrodes made with rapid prototyping and the electroforming process Fulltext Access 7 Pages 2005
On the hot working characteristics of 2014 Al-20Â vol% Al2O3 metal matrix composite Fulltext Access 7 Pages 2005
The polishing of molds and dies using a compliance tool holder mechanism Fulltext Access 7 Pages 2005
Development of processing map for 6061 Al/15% SiCp through neural networks Fulltext Access 7 Pages 2005
The kinetic of induced martensitic formation and its effect on forming limit curves in the AISI 304 stainless steel Fulltext Access 7 Pages 2005
Mathematical modeling and computer simulation of molten metal cleansing by the rotating impeller degasser Fulltext Access 7 Pages 2005
Precision design of roll-forging die and its application in the forming of automobile front axles Fulltext Access 7 Pages 2005
Three-dimensional thermo-elastic-plastic coupled FEM simulations for metal oblique cutting processes Fulltext Access 7 Pages 2005
The electrical conductivity of laser-remelted and plasma-sprayed Ni and Cr coatings Fulltext Access 7 Pages 2005
Field synergy optimization and enhanced heat transfer by multi-longitudinal vortexes flow in tube Fulltext Access 7 Pages 2005
Numerical determination of strain localisation during finite element simulation of deep-drawing operations Fulltext Access 7 Pages 2005
A note on the conceptual design of polymeric composite automotive bumper system Fulltext Access 7 Pages 2005
A novel method for net-shape forming of hypereutectic Al-Si alloys by thixocasting with powder preforms Fulltext Access 7 Pages 2005
Development and characterization by HRTEM of hot-pressed Si3N4-SiC(w) composites Fulltext Access 7 Pages 2005
Simulation of the deformation and stress distribution within a flexible material pressed by a pinch gripper Fulltext Access 7 Pages 2005
Comparison between genetic algorithms and response surface methodology in GMAW welding optimization Fulltext Access 7 Pages 2005
Numerical simulation of deposition process for a new 3DP printhead design Fulltext Access 7 Pages 2005
FEM simulation on microstructure of DC flash butt welding for an ultra-fine grain steel Fulltext Access 7 Pages 2005
Cutting and wearing characteristics of TiC-based cermets cutters with nano-TiN addition Fulltext Access 7 Pages 2005
Finite element simulation of multi-point sheet forming process based on implicit scheme Fulltext Access 7 Pages 2005