کد مقاله کد نشریه سال انتشار مقاله انگلیسی نسخه تمام متن
4923393 1430693 2017 17 صفحه PDF دانلود رایگان
عنوان انگلیسی مقاله ISI
Stability study on structural systems assembled by system scaffolds
ترجمه فارسی عنوان
مطالعه پایداری سیستم های ساختاری که توسط داربست های سیستم ساخته شده اند
کلمات کلیدی
خم شدن بار بحرانی، نیروی جانبدارانه، تجزیه و تحلیل ناپیوسته مرتبه دوم، سیستم داربست،
ترجمه چکیده
این تحقیق به بررسی ثبات سیستم های سازه ای مونتاژ شده توسط داربست های سیستم می پردازد. آزمایش بارگیری بر روی سیستم های ساختمان تک بیت سیستم و سیستم ساختاری در سطح مقدماتی در فضای باز ساخته شده توسط داربست سیستم است. نتایج آزمون با روش تحلیل ناپیلاسی دوم مرتبه با مفاصل نیمه سفتی برای تعیین قابلیت اطمینان پارامترهای تحلیلی مختلف مقایسه شد. مطالعه نشان می دهد که در حالی که مدل شکست یک سیستم دو طبقه تک بانی بدون داربست های مورب به طور کلی شکستگی شکستگی ساختار است، مدل شکست ساختار مشابه با پرانتز مورب شکست ناپذیری از استانداردهای عمودی بین بالا و طبقه پایین تر بار بحرانی پیکربندی با پرانتز مورب دو برابر همان ساختار بدون پرانتز مورب است. در زمان شکستن خمش در دو طبقه، دوبعدی، شش طبقه ساختمان ساختاری که توسط داربست های سیستم جمع شده بودند، سطح عمودی در چهار گوشه به نظر می رسید که دارای جابجایی های افقی بزرگی به علت عدم اتصال به قطر مورب است. با این حال، استاندارد عمودی در مرکز تغییر شکل افقی آشکار را نشان نداد، زیرا با چهار تسمه مورب تقویت شده بود. علاوه بر این، استفاده از پرانتز مورب می تواند ظرفیت بارگذاری استانداردهای عمودی را به طور قابل توجهی افزایش دهد. این مطالعه توصیه می کند که تمام استانداردهای عمودی با باند های مورب تقویت شود تا ظرفیت بار سیستم های سازه ای که توسط داربست های سیستم جمع می شوند، تضمین شود. برای تعیین بارهای بحرانی سیستم های ساختاری در مقیاس مونتاژ شده توسط داربست های سیستم توصیه می شود که تجزیه و تحلیل ناپیوستگی مرتبه دوم با مفاصل نیمه سفت و نیروهای جانبی مختلف صورت گیرد.
موضوعات مرتبط
مهندسی و علوم پایه سایر رشته های مهندسی مهندسی عمران و سازه
چکیده انگلیسی
This study investigates the stability of the structural systems assembled by system scaffolds. Loading tests were conducted on the indoor single-bay system scaffolds and the outdoor full-scale structural system assembled by system scaffolds. Test results were compared with the second-order inelastic analysis with semi-rigid joints to determine the reliability of various analytical parameters. The study reveals that, while the failure model of the single-bay two-storey system scaffold without diagonal braces is overall buckling failure of the structure, the failure model of the same structure with diagonal braces is buckling failure of the vertical standards between the upper and lower storeys. The critical load of the configuration with diagonal braces is about double that of the same structure without diagonal braces. At the moment of buckling failure of the outdoor full-scale two-row, two-bay, six-storey structural system assembled by system scaffolds, the vertical standards at the four corners appeared to have large horizontal displacements owing to without diagonal braces. However, the vertical standard in the center did not exhibit obvious horizontal deformation because it was reinforced with diagonal braces on four sides. In addition, the use of diagonal braces can significantly increase the load capacity of vertical standards. This study recommends that all vertical standards be reinforced with diagonal braces to ensure the load capacity of the structural systems assembled by system scaffolds. A second-order inelastic analysis with semi-rigid joints and various notional lateral forces is recommended to determine the critical loads of full-scale structural systems assembled by system scaffolds.
ناشر
Database: Elsevier - ScienceDirect (ساینس دایرکت)
Journal: Journal of Constructional Steel Research - Volume 137, October 2017, Pages 135-151
نویسندگان
, , , ,