کد مقاله | کد نشریه | سال انتشار | مقاله انگلیسی | نسخه تمام متن |
---|---|---|---|---|
4986936 | 1454959 | 2016 | 8 صفحه PDF | دانلود رایگان |
عنوان انگلیسی مقاله ISI
Influence of pre-existing martensite on the wear resistance of metastable austenitic stainless steels
ترجمه فارسی عنوان
تأثیر مارتنزیتی که در گذشته وجود داشت، بر مقاومت در برابر سایش فولادهای ضد زنگ آستنیتی متاستاز است
دانلود مقاله + سفارش ترجمه
دانلود مقاله ISI انگلیسی
رایگان برای ایرانیان
کلمات کلیدی
فولاد ضد زنگ آستنیتی متاستاز، مارتنزیت، سایش کشویی، تکنیک های توصیف پیشرفته،
ترجمه چکیده
اثر مارتنزیتی که از قبل وجود داشت بر روی رفتار سایش کششی یک فولاد ضد زنگ آستنیتی متاستاز تجاری تجاری مورد بررسی قرار گرفت. دو شرایط مختلف فولاد در نظر گرفته شد: آنیل (با ریز ساختار کامل آستنیتی) و سرد نورد، شامل مخلوط آستنیت و مارتنزیت. تست های پوششی با استفاده از توپ در روش دیسک با سرعت ثابت و فاصله های مختلف کشویی انجام شد. همبستگی بین ریزساختار و مکانیزم های پوششی با پراش اشعه ایکس، پراش الکترونی پراکنده و پرتو یون فوکوس انجام شد. نتایج نشان می دهد که مقاومت به سایش در افزایش مقدار مارتنزیت از قبل وجود دارد. در این معنی، مارتنزیت ناشی از فشار بیشتر برای نمونه های سرد سرد ساخته شده، سخت شدن سطح و در نتیجه کاهش تشکیل گوه، که باعث حذف مواد از سطح است. تجزیه و تحلیل دقیق مسیر سایش، تشکیل یک لایه فوق العاده دانه را فقط در زیر سطح، نه تنها برای ورق نورد، بلکه برای فولاد نورد سرد نیز نشان داد.
موضوعات مرتبط
مهندسی و علوم پایه
مهندسی شیمی
شیمی کلوئیدی و سطحی
چکیده انگلیسی
The effect of pre-existing martensite on the sliding wear behavior of a commercial metastable austenitic stainless steel was investigated. Two different steel conditions were considered: annealed (with a fully austenitic microstructure) and cold rolled, consisting of mixtures of austenite and martensite. Wear tests were carried out using ball on disc technique at constant velocity and different sliding distances. Correlation between microstructure and wear mechanisms was performed by X-ray diffraction, electron back-scattered diffraction and focus ion beam. Results show that wear resistance decreases at increasing the amount of pre-existing martensite. In this sense, more strain-induced martensite developed for cold rolled samples, hardening the surface and consequently reducing wedge formation, which induced material removal from the surface. The detailed analysis of the wear track demonstrated the formation of an ultrafine-grain layer just below the surface, not only for annealed but also for cold rolled steel.
ناشر
Database: Elsevier - ScienceDirect (ساینس دایرکت)
Journal: Wear - Volumes 364â365, 15 October 2016, Pages 40-47
Journal: Wear - Volumes 364â365, 15 October 2016, Pages 40-47
نویسندگان
G. Fargas, J.J. Roa, A. Mateo,