کد مقاله | کد نشریه | سال انتشار | مقاله انگلیسی | نسخه تمام متن |
---|---|---|---|---|
7003771 | 1454936 | 2018 | 18 صفحه PDF | دانلود رایگان |
عنوان انگلیسی مقاله ISI
A new approach to the description of height distribution of plateau honed cylinder liner surface texture during the initial stage of wear
ترجمه فارسی عنوان
یک رویکرد جدید به توصیف توزیع ارتفاع بتنی سطح سیلندر با سطح فلات در طول مرحله اولیه پوشیدن
دانلود مقاله + سفارش ترجمه
دانلود مقاله ISI انگلیسی
رایگان برای ایرانیان
کلمات کلیدی
بافت سطح، توزیع ارتفاع، بوش سیلندر، پوشیدن، در حال اجرا در،
ترجمه چکیده
این مقاله روش جدیدی را برای توصیف توزیع ارتفاع ورق سطحی سطوح سیلندر فلوته پس از مرحله اولیه پوشیدن ارائه می دهد. در ادبیات، مدل دوگاوس اغلب برای توصیف توزیع ارتفاع سطوح لاینر سیلندر استفاده می شود. با این حال، در مورد سطح افقی فلات، در طول دوره در حال اجرا تغییرات مختلفی از سطح رخ می دهد، عمدتا شامل فرسایش و یا تغییر شکل پلاستیک از بالاترین قله ها واقع در منطقه فلات. بنابراین برای توصیف توزیع ارتفاع سطح فلات در طول مرحله در حال اجرا یا اولیه، یک مدل تحلیلی به نام سه گاوسی استفاده شد. این مدل برای تعیین توزیع ارتفاع سطح سیلندر پس از مرحله اولیه سایش استفاده شد. با استفاده از این مدل، سطوح مختلف سطح فلات با ردیابی سایش با استفاده از این مدل مورد تجزیه و تحلیل قرار گرفت و برخی از آنها به عنوان نمونه های معمول در این مقاله ارائه شده است. نتایج استفاده از مدل سه گاوسی برای توصیف توزیع ارتفاع بافت سطح بعد از مرحله اولیه پوشیدن، با رویکرد موجود دوگاوس، مقایسه شده است. مقایسه تناسب این دو مدل با توزیع ارتفاع بافت سطحی فلات بعد از مرحله اولیه پوشیدن، نشان می دهد که مدل سه گاوسی داده ها را بهتر از مدل دو گاوسی سازگار می کند. نتایج مشاهده شده، اندازه گیری شده و محاسبه شده روشن و اظهار می شود.
موضوعات مرتبط
مهندسی و علوم پایه
مهندسی شیمی
شیمی کلوئیدی و سطحی
چکیده انگلیسی
This article presents a new approach to the description of the height distribution of plateau honed cylinder liner surface topography after the initial stage of wear. In the literature, the two-Gaussian model is often used to describe the height distribution of cylinder liner surfaces. However, in the case of plateau honed surfaces, during the running-in period different changes of surface take place, mostly involving truncation or plastic deformation processes of the highest summits located in the plateau area. Therefore, to describe the height distribution of plateau honed surfaces during the running-in or initial stage of wear, an analytical model called three-Gaussian was used. This model was applied to determine the surface height distribution of cylinder liner after the initial stage of wear. Many plateau honed surfaces with traces of wear were analysed using this model, and some of them are shown as typical examples in this paper. The results of use of the three-Gaussian model to describe the height distribution of surface texture after the initial stage of wear are compared with the existing two-Gaussian approach. A comparison of the fit of these two models to the height distribution of plateau honed surface texture after the initial stage of wear shows that the three-Gaussian model fits the data better than the two-Gaussian model. The observed, measured and calculated results are elucidated and commented on.
ناشر
Database: Elsevier - ScienceDirect (ساینس دایرکت)
Journal: Wear - Volumes 408â409, 15 August 2018, Pages 34-42
Journal: Wear - Volumes 408â409, 15 August 2018, Pages 34-42
نویسندگان
W.A. Grabon,