کد مقاله کد نشریه سال انتشار مقاله انگلیسی نسخه تمام متن
7004779 1454998 2013 27 صفحه PDF دانلود رایگان
عنوان انگلیسی مقاله ISI
Adhesive transfer in aero-engine abradable linings contact
ترجمه فارسی عنوان
انتقال چسبنده در تماس با لنت های قابل انفجار هواپیما
کلمات کلیدی
قابل جدا شدن چسبندگی، انعطاف پذیری، هوافضا،
ترجمه چکیده
پوشیده از لنت های رفع شده بر روی یک پلت فرم مجهز به تست معکوس مورد بررسی قرار گرفته است، ایجاد دوباره ساز و کار پوشیدن بین نوک تیغه و مواد قابل تمیز که در کمپرسور هواپیما رخ می دهد. مشخصه فرآیند سایش با استفاده از یک روش تصویربرداری استروبوسکوپی انجام شده است، قادر به بررسی ماهیت ضربه نوک تیغه بر ریزش و انتقال چسب ماده به نوک تیغه در طی آزمون است. در آزمایشاتی که میزان حملات کمی را نشان داد، انتقال چسبناک مشاهده شد، در حالی که با شدت بیشتر درگیری، رفتار برش مشاهده شد. تجزیه و تحلیل با تکنیک تصویربرداری استروبوسکوپی اجازه انتقال چسب در طول آزمون را به عنوان یک اثر از طول مورب ثبت می کند. سه مرحله برای انتقال چسبندگی در طی آزمایش تعیین شد. فاز شروع با سرعت کم چسبندگی، چسبندگی حالت پایدار و شکستگی مواد پیوسته و پس از آن دوباره شروع می شود. این نتایج همچنین نشان می دهد که چگونه عمل استاندارد انجام تجزیه و تحلیل مواد پایدار در پایان آزمایش، لزوما به طور واضح مکانیک کلی انتقال چسب را مشخص نمی کند.
موضوعات مرتبط
مهندسی و علوم پایه مهندسی شیمی شیمی کلوئیدی و سطحی
چکیده انگلیسی
Wear of abradable linings has been investigated on a scaled test rig platform, re-creating the wear mechanisms observed between the blade tip and abradable material that occur in an aero-engine compressor. The characterisation of the wear process has been performed using a stroboscopic imaging technique, capable of investigating the nature of the blade tip strike on the abradable, and the adhesive transfer of the material to the blade tip during a test. It was found in tests with low incursion rates that there was adhesive transfer, whereas with high incursion rates a cutting behaviour was observed. Analysis with the stroboscopic imaging technique allowed the adhesive transfer during the test as a function of the rub length to be recorded. Three phases were identified for adhesive transfer during test; an initiation phase with low rate of adhesion, steady state adhesion, and fracture of adhered material followed by re-initiation. These results also highlight how the standard practice of performing analysis of adhered material at the end of a test does not necessarily characterise the overall mechanics of adhesive transfer satisfactorily.
ناشر
Database: Elsevier - ScienceDirect (ساینس دایرکت)
Journal: Wear - Volume 304, Issues 1–2, 15 July 2013, Pages 202-210
نویسندگان
, , ,