کد مقاله کد نشریه سال انتشار مقاله انگلیسی نسخه تمام متن
7171032 1463466 2016 11 صفحه PDF دانلود رایگان
عنوان انگلیسی مقاله ISI
Adhesive material property evaluation for improved Lamb wave simulation
ترجمه فارسی عنوان
ارزیابی اموال مواد چسب برای بهبود شبیه سازی موج شانه
ترجمه چکیده
امواج بره به طور معمول در فلزات ایزوتروپیک مانند فولاد و آلومینیوم ساخته شده اند که خواص مشهور منتشر شده را دارند. هنگام تلاش برای مدل سازی امواج لامب در مواد پلیمری با خواص ویسکولا الاستیک مانند چسب اپوکسی، خواص منتشر شده که معمولا بر اساس تست مکانیکی شبه استاتیک است، تکیه نمی کنند. این به خاطر امواج لامب ایجاد اختلال الاستیک با دامنه نسبتا کم فشار، اما نرخ بالای فشار است. برخلاف فلزات، مدول یک ماده ویسکولاستیک وابسته به میزان فشار است. بنابراین برای رفتار دقیق امواج بره در پلیمرها، خواص ساختار میزبان باید با استفاده از روش های تولید شده که دامنه های فشار و نرخ کرنش برنامه مورد نظر را تولید می کنند، بدست آید. این مقاله، بررسی سه روش اولتراسونیک برای تعیین خواص مواد یک چسب فیلم را ارائه می دهد. بدست می آید که مدول الاستیک مورد نیاز برای دقت امواج امواج لام در این چسب تقریبا 60٪ بالاتر از مقدار تعیین شده توسط آزمون های شبه استاتیک معمول است. در نهایت، یک شبیه سازی موج بره برای نشان دادن این است که چنین اختلافات می تواند منجر به اختلاف معنی دار در میدان موج پراکنده از نقص خط پیوند شود.
موضوعات مرتبط
مهندسی و علوم پایه سایر رشته های مهندسی مهندسی مکانیک
چکیده انگلیسی
Lamb waves are commonly modelled in isotropic metals such as steel and aluminium which have well-known published properties. When attempting to model Lamb waves in polymer materials with viscoelastic properties such as epoxy adhesives, it is not sufficient to rely on published properties which are usually based on quasi-static mechanical testing. This is due to Lamb waves creating an elastic disturbance with a relatively low strain amplitude but high strain rate. Unlike in metals, the modulus of a viscoelastic material is dependent on strain rate. Therefore to accurately model the behaviour of Lamb waves in polymers, the properties of the host structure must be obtained using methods that reproduce the strain amplitudes and strain rates of the intended application. This paper presents an investigation of three ultrasonic methods for determining the material properties of a film adhesive. It is found that the elastic modulus required to accurately model Lamb waves in this adhesive is approximately 60% higher than the value determined by conventional quasi-static testing. Finally, a Lamb wave simulation is used to illustrate that such discrepancies can lead to significant differences in the scattered wave field from a bond-line defect.
ناشر
Database: Elsevier - ScienceDirect (ساینس دایرکت)
Journal: International Journal of Adhesion and Adhesives - Volume 71, December 2016, Pages 28-38
نویسندگان
, , , ,