کد مقاله | کد نشریه | سال انتشار | مقاله انگلیسی | نسخه تمام متن |
---|---|---|---|---|
7174082 | 1464972 | 2016 | 16 صفحه PDF | دانلود رایگان |
عنوان انگلیسی مقاله ISI
Influence of roller distribution modes on spinning force during tube spinning
ترجمه فارسی عنوان
تأثیر حالت های توزیع غلتکی بر نیروی چرخش در طی چرخش لوله
دانلود مقاله + سفارش ترجمه
دانلود مقاله ISI انگلیسی
رایگان برای ایرانیان
کلمات کلیدی
لوله ریسندگی، نیروی چرخش توزیع غلتک، منطقه تماس
ترجمه چکیده
نیروی خارج از مرکز بر روی مهره توسط غلطک تأثیر مهمی بر دقت تشکیل قطعه های لوله ای در طی چرخش لوله دارد که نزدیک به حالت توزیع غلتکی مرتبط است. در این مطالعه، ویژگی های تغییر شکل و نیروهای چرخشی در طی چرخش لوله با حالت های مختلف توزیع غلتکی مورد بررسی قرار گرفت. با توجه به نتایج شبیه سازی، مناطق تماس زیر غلتک ها مورد تجزیه و تحلیل قرار گرفته و نیروهای چرخشی توسط غلطک های مختلف به دست آمده است. نتایج نشان می دهد که توزیع تنش نشان دهنده تغییر غیر دوره ای در امتداد محور دور و نیروهای چرخشی از غلتک های مختلف متفاوت است، زیرا توزیع غول یکنواخت غلطک ها به مناطق مختلف تماس زیر غلتک منجر می شود. تنوع نیروهای چرخشی غلتک باعث بار بار نامتعادل بر روی هسته می شود، بنابراین محور از محور خنثی منحرف می شود، که توسط اندازه گیری انحراف از انتهای مهره در آزمایش چرخش تایید شده است. اگر چه نیروهای چرخشی غلطک ها در یک طرف متفاوت هستند، چرخش چهار غلتکی می تواند مانور را حفظ کند. علاوه بر این، نوسان چرخش با سه غلطک غیر توزیع شده اخیرا پیشنهاد شده است تا توازن هسته را به دست آورده و انعطاف پذیری دستگاه چرخش دوطرفه سنتی را افزایش دهد.
موضوعات مرتبط
مهندسی و علوم پایه
سایر رشته های مهندسی
مهندسی مکانیک
چکیده انگلیسی
The eccentric force exerted on the mandrel by the rollers has important influence on the forming precision of tubular workpieces during tube spinning, which is closely related to the roller distribution mode. In this study, the deformation characteristics and spinning forces were investigated during tube spinning with different roller distribution modes. According to the simulation results, the contact zones under the rollers were analyzed and the spinning forces applied by various rollers were obtained. The results show that the stress distribution exhibits non-periodic change along circumferential direction and the spinning forces of various rollers are different because the non-uniform distribution of the rollers leads to different contact zone areas under the rollers. The variation of spinning forces of the rollers causes the unbalanced load exerted on the mandrel, thus the mandrel deviates from the neutral axis, which is verified by the deflection measurement of the mandrel end in the spinning experiment. Although the spinning forces of the rollers on the same side are different, four-roller spinning can keep the balance of the mandrel. In addition, stagger spinning with nonuniformly distributed three rollers is newly proposed to achieve the balance of the mandrel, increasing the flexibility of traditional two-roller spinning machine.
ناشر
Database: Elsevier - ScienceDirect (ساینس دایرکت)
Journal: International Journal of Mechanical Sciences - Volume 113, July 2016, Pages 10-25
Journal: International Journal of Mechanical Sciences - Volume 113, July 2016, Pages 10-25
نویسندگان
Wenchen Xu, Xiaokai Zhao, Hao Ma, Debin Shan, Henglong Lin,