کد مقاله کد نشریه سال انتشار مقاله انگلیسی نسخه تمام متن
7175341 1466377 2018 30 صفحه PDF دانلود رایگان
عنوان انگلیسی مقاله ISI
Optimal design of rotary compressor oriented to end-plate gas injection with check valve
ترجمه فارسی عنوان
طراحی مطلوب کمپرسور چرخشی جهت تزریق گاز با پایان لوله با سوپاپ
کلمات کلیدی
کمپرسور روتاری تزریق گاز، پایان تزریق، طراحی مطلوب، کمپرسور روتاری تزریق گاز، تزریق به صفحه پایان طراحی مطلوب
ترجمه چکیده
تکنولوژی تزریق گاز به منظور افزایش عملکرد کمپرسور چرخشی تک سیلندر با نسبت فشرده سازی بالا توسعه داده شد. با این حال، بهبود طرح های جاری به دلیل کمترین جرم مؤثر تزریق شده رضایتبخش بود. یک ساختار جدید تزریق با ورق انتهایی با دریچه سوپاپ برای کمپرسور روتاری پیشنهاد شد و مزایای آن در یک مطالعه قبلی تایید شد. برای افزایش پورت تزریق، تزریق گاز را افزایش می دهد و در نهایت افزایش عملکرد را افزایش می دهد، عبارات عمومی پاکت ها و مناطق ناحیه تزریق بر اساس روش هندسی تحلیلی در این مقاله طراحی شده است. بر اساس آنها، اثرات پارامترهای طراحی، مانند بیحرکتی و ضخامت پیستون غلتکی، در منطقه منطقه تزریق بررسی می شود. در نهایت، یک روش طراحی بهینه برای کمپرسور چرخشی که به پیشنهاد تزریق گاز پایه صفحه با سوپاپ مطرح شده است، مطرح شده است. به عنوان یک نتیجه گیری، برای یک کمپرسور چرخان دلخواه با شعاع سیلندر مشخص شده، منطقه ناحیه تزریق حداکثر زمانی که ضخامت پیستون غلتکی برابر با دو برابر بی ثباتی است، به حداکثر می رسد.
موضوعات مرتبط
مهندسی و علوم پایه سایر رشته های مهندسی مهندسی مکانیک
چکیده انگلیسی
The gas injection technology had been developed to enhance the performance of the single cylinder rotary compressor at high compression ratio. However, the improvement of current designs was unsatisfactory because of the limited effective mass injected. A novel end-plate injection structure with check valve for rotary compressor was proposed and its advantages were confirmed in a previous study. In order to enlarge the injection port, increase the gas injected, and eventually increase performance enhancement, the general expressions of the envelopes and areas of the injection regions are developed based on an analytical geometry method in this paper. Based on them, the effects of the design parameters, such as the eccentricity and the thickness of the rolling piston, on the injection region area are investigated. Finally, an optimal design method for the rotary compressor oriented to proposed end-plate gas injection with check valve is raised. As a conclusion, for an arbitrary rotary compressor with designated cylinder radius, the area of the injection region reaches the maximum when the thickness of the rolling piston is equal to two times of the eccentricity.
ناشر
Database: Elsevier - ScienceDirect (ساینس دایرکت)
Journal: International Journal of Refrigeration - Volume 88, April 2018, Pages 516-522
نویسندگان
, , , ,