کد مقاله کد نشریه سال انتشار مقاله انگلیسی نسخه تمام متن
7176296 1466708 2018 26 صفحه PDF دانلود رایگان
عنوان انگلیسی مقاله ISI
Temperature-based method for determination of feed increments in crankshaft grinding
ترجمه فارسی عنوان
روش مبتنی بر دما برای تعیین افزایش خوراک در سنگ زنی میل لنگ
کلمات کلیدی
ترجمه چکیده
طراحی چرخه میل لنگ شامل تعیین میزان ورودی شعاعی و محوری در هر بار افزایش خوراک است. یک روش جدید برای تعیین افزایش خوراک برای افزایش بهره وری و جلوگیری از آسیب های حرارتی ایجاد شده است. تجزیه و تحلیل هندسه، سینماتیک و ویژگی های انرژی خاص برای تخمین توزیع وابسته به خوراک حداکثر دمای سطح در امتداد پروفایل چرخ ساخته شده است. کشف شده است که در طول زمان تغذیه هر دو محوری و شعاعی دو منطقه حداکثر دما وجود دارد. بنابراین، روش توسعه یافته، الزامات را تعیین می کند به طوری که یک آستانه رایت پیش تعیین شده در این دو نقطه بحرانی مطابقت دارد. تکنولوژی جدید با اندازه گیری سر و صدای بارکوهوزن و استرس باقی مانده معتبر است. مقایسهای بین روش مبتنی بر دما و روش رادیال غرق شده که قبلا در تولید استفاده شده است، مقایسه شده است. این مقایسه نشان می دهد که زمان چرخه کمتر با خطر کمتر آسیب های حرارتی قابل دستیابی است. نتایج برای میزان حذف مواد و حداکثر دمای سطح نیز ارائه شده است.
موضوعات مرتبط
مهندسی و علوم پایه سایر رشته های مهندسی مهندسی صنعتی و تولید
چکیده انگلیسی
The design of a crankshaft-grinding cycle involves determining the radial infeed and axial infeed in each feed increment. A new method for determination of feed increments is developed to increase productivity while avoiding thermal damage. Analyses of the geometry, kinematics and specific-energy characteristic are made to estimate the feed-dependent distribution of maximum surface temperature along the wheel profile. It is discovered that there are two temperature maxima in the grinding zone when feeding both axially and radially. Therefore, the developed method determines the infeeds such that a predetermined burn threshold is matched in these two critical points. The new technology is validated by measurements of Barkhausen noise and residual stress. A comparison is made between the temperature-based method and the radial-plunge method previously used in production. The comparison indicates that lower cycle times are attainable with less risk of thermal damage. Results for material-removal rate and maximum surface temperature are also presented.
ناشر
Database: Elsevier - ScienceDirect (ساینس دایرکت)
Journal: Journal of Materials Processing Technology - Volume 259, September 2018, Pages 228-234
نویسندگان
, , , ,