کد مقاله کد نشریه سال انتشار مقاله انگلیسی نسخه تمام متن
816676 1469280 2016 4 صفحه PDF دانلود رایگان
عنوان انگلیسی مقاله ISI
Dynamic compressive behaviour of aluminium foams fabricated from rejected precursor materials
ترجمه فارسی عنوان
رفتار فشاری پویا از فوم های آلومینیومی ساخته شده از مواد پیش رفته رد شده است
کلمات کلیدی
فوم آلومینیوم، رفتار فشرده سازی یک جانبه، مکانیزم تغییر شکل
ترجمه چکیده
هدف از این مطالعه بررسی مکانیزم های تغییر شکل و شکست مکانیکی بلوک های مستطیلی آلومینیوم فوم ساخته شده از پیش رسیده های رد شده با استفاده از تست های فشرده سازی یکپارچه پویا توسط ترموگرافی مادون قرمز میانی می باشد. رفتار فشاری دینامیکی این فوم ها با رفتار بلوک های فوم تهیه شده از یک پیش ماده سنتی مقایسه شد. نتایج نشان می دهد که فوم های پیش رونده رد شده در شکل پایین تر با تغییر شکل موضعی در سطح فوم پراکنده شده و منجر به تشکیل بسیاری از باندهای تغییر شکل می شوند، در حالی که نمونه های مرجع (ساخته شده از یک پیش ماده) تنها تعداد کمی از نوارهای تغییر شکل عمدتا در انتهای پایین و بالا قرار دارند. باند ها در ضعیف ترین نقاط نمونه رخ می دهند، که در مورد نمونه هایی که از قبل پیش رانده شده اند، با مناطق اتصال در فوم بوسیله پیش ماده های مختلفی که در طی فرایند فوم استفاده می شود، مطابقت دارند. در این ناحیه اتصالات، نقص های ساختاری ایجاد شده است، به عنوان مثال میکروپورها باعث افزایش غلظت استرس برای شروع ترک می شوند. نتایج همچنین نشان می دهد که منطقه فلات منحنی های فشار تنش فشاری (استرس به تدریج با افزایش فشار افزایش می یابد) بیشتر در مورد فوم از قطعه پیش رونده رد نسبت به مقادیر مرجع بیشتر است.
موضوعات مرتبط
مهندسی و علوم پایه سایر رشته های مهندسی مهندسی (عمومی)
چکیده انگلیسی
The work aims to study the deformation and failure mechanisms of rectangular aluminium foam blocks prepared from rejected precursors using dynamic uniaxial compressive tests supported by middle-wave infrared thermography. The dynamic compressive behavior of these foams was compared to the behavior of the foam blocks prepared from a traditional single precursor. The results indicate that the foams from rejected precursors begin to deform at lower strain with local deformation dispersed at the foam surface leading to the formation of many deformation bands, while the reference samples (fabricated from a single precursor) present only few deformation bands which are mainly located at their lower and upper ends. The bands occur at the weakest points of the samples, which in case of the samples made of rejected precursors correspond to the joining regions formed within the foam by the different precursors used during the foaming process. In these joining regions imperfections and structural defects are developed, i.e. micropores promoting a stress concentration for crack initiation. The results also indicate that the plateau region of the compressive stress-strain curves (the stress gradually increases with increasing strain) is much more inclined in case of the foams from rejected precursor pieces compared to the reference ones.
ناشر
Database: Elsevier - ScienceDirect (ساینس دایرکت)
Journal: Ciência & Tecnologia dos Materiais - Volume 28, Issue 1, January–June 2016, Pages 19-22
نویسندگان
, , ,