کد مقاله | کد نشریه | سال انتشار | مقاله انگلیسی | نسخه تمام متن |
---|---|---|---|---|
7159710 | 1462808 | 2017 | 7 صفحه PDF | دانلود رایگان |
عنوان انگلیسی مقاله ISI
Rate of injection measurements of a direct-acting piezoelectric injector for different operating temperatures
ترجمه فارسی عنوان
نرخ اندازه گیری تزریق یک انژکتور پیزو الکتریکی مستقیم برای دمای عملیاتی مختلف
دانلود مقاله + سفارش ترجمه
دانلود مقاله ISI انگلیسی
رایگان برای ایرانیان
کلمات کلیدی
تزریق دیزلی، مستقیم عمل میزان تزریق، دمای کار،
ترجمه چکیده
همانطور که مقررات انتشار آلاینده ها در موتورهای دیزلی به طور فزاینده ای محدود می شود، معرفی پیزوالکتریک انژکتورهای مستقیم مستقیم به دنبال بهبود کلی عملکرد سیستم تزریق و در نتیجه کاهش آلاینده های احتراق است. در چنین سیستمی، پیمان سوزن توسط شارژ یا ولتاژ اعمال می شود به پشته پیزو، اجازه می دهد تا کنترل دقیق تر از فرآیند تزریق سوخت را کنترل کند. اگر چه شناخته شده است که عملکرد بلورهای پیزوالکتریک بستگی به دمای عملیات آن دارد، اثر آن بر میزان تزریق هنوز مشخص نیست. در این تحقیق برای تعیین میزان تزریق انژکتور مستقیم مستقیم برای دمای عملیاتی مختلف از یک راه اندازی خاص استفاده شد. آن را به یک شاخص منحنی تخلیه میزان تزریق با یک دارنده خاص است که آستین خنشی متصل به یک مدار اتیلن گلیکول است، که توسط واحد گرما کنترل رانده شده است. یک ولتاژ کنترل پشته های مختلف برای سه فشار خطی و درجه حرارت کارایی پارامتریک انجام شد. در نتیجه، هنگامی که لیزر سوزن بر جریان جریان داخلی نفوذ نمی کند، میزان تزریق با فشار تزریق کنترل می شود، با حداقل تاثیر از دمای کار، شبیه به نتایج انژکتور های هیدرولیکی معمول است. در بخش سوزن ناپایدار، دو ناحیه عامل مشاهده شده، توسط یک سطح ولتاژ مشخص مشخص شده اند. بالای آن دتکتور سوزن توانست با دقت کنترل جریان سوخت جرم را کنترل کند. اما در زیر آن، نرخ ثابت قیمت تزریق شدیدا کاهش یافت. نرخ این کاهش فقط به فشار تزریق بستگی دارد. سطح آستانه، به نام ولتاژ بحرانی، به طور خطی با افزایش فشار تزریق و دمای کار افزایش می یابد. همچنین برای حفظ جریان جریان جامد سوخت برای کاهش دمای عملیاتی، سطح ولتاژ سیگنال کنترل باید کاهش یابد. این نتایج اهمیت نظارت و کنترل شرایط عملیات انژکتورهای مستقیم مستقیم را برجسته می کند، زیرا عملکرد و کارایی آنها هم تحت تاثیر دمای کار پشته پیزو است.
موضوعات مرتبط
مهندسی و علوم پایه
مهندسی انرژی
انرژی (عمومی)
چکیده انگلیسی
As the regulations for pollutant emissions in diesel engines are increasingly restrictive, the introduction of the piezoelectric direct-acting injectors seeks to improve the overall efficiency of the injection system, and consequently reduce combustion contaminants. In such systems, the needle lift is governed by the charge, or voltage, applied to the piezo stack, allowing for a more precise control over the fuel injection process. Although it is known that the performance of the piezoelectric crystals depends on its temperature of operation, the effect this has on the rate of injection is still unclear. In this research, a particular setup was used to measure the rate of injection of a direct-acting injector for different operating temperatures. It was mounted into an injection discharge rate curve indicator with a particular holder that has a cooling sleeve connected to a circuit running ethylene glycol, which is driven by a thermoregulator unit. A parametric sweep of different piezo stack control voltages for three rail pressures and operating temperatures was carried out. On the results, when needle lift does not influence internal flow development, the rate of injection was controlled by the injection pressure, with minimal impact from the working temperature, resembling results from conventional hydraulic injectors. At partial needle lift, two operating regions were observed, delimited by a particular voltage level. Above it, the needle throttling was able to control mass fuel flow accurately. But below it, the stabilized rate of injection values decreased drastically. The rate of this decline was dependent only on the injection pressure. The threshold level, named critical voltage, increased linearly with increasing injection pressure and working temperature. Also, to maintain a constant fuel mass flow for decreasing operating temperature, the voltage level of the control signal had to be reduced. These results highlight the importance of monitoring and controlling the operating conditions of the direct-acting injectors, as their performance and efficiency are both influenced by the working temperature of the piezo stack.
ناشر
Database: Elsevier - ScienceDirect (ساینس دایرکت)
Journal: Energy Conversion and Management - Volume 154, 15 December 2017, Pages 387-393
Journal: Energy Conversion and Management - Volume 154, 15 December 2017, Pages 387-393
نویسندگان
Raul Payri, Jaime Gimeno, Carmen Mata, Alberto Viera,