کد مقاله کد نشریه سال انتشار مقاله انگلیسی نسخه تمام متن
1573438 1514681 2016 7 صفحه PDF دانلود رایگان
عنوان انگلیسی مقاله ISI
Microstructure and mechanical properties of internal crack healing in a low carbon steel
ترجمه فارسی عنوان
ریز ساختار و خواص مکانیکی شفا خوردگی داخلی در یک فولاد کم کربن
ترجمه چکیده
رفتار رفتار شکستن کوتاهی در کلی فولاد کوچک در دمای بالا بررسی شد. ترکهای داخلی به وسیله روش حفاری و فشرده سازی به نمونه های فولادی کم کربن معرفی شدند. میکروسکوپ میکروسکوپ نوری و میکروسکوپ الکترونی اسکن میکروسکوپ میکروسکوپ نوری با استفاده از میکروسکوپ الکترونی را مشاهده کردند. خواص مکانیکی منطقه شفا خوردگی در دمای اتاق آزمایش شد. نتایج نشان می دهد که دو مکانیزم شفا خوردن در فولاد کم کربن وجود دارد. بهبودی کراک توسط انتشار اتمی در دماهای پایین ایجاد می شود و عمدتا بستگی به کریستالیزاسیون و رشد دانه در دماهای بالاتر دارد. تکامل میکرو سازمانی منطقه بهبودی شکاف را می توان به چهار مرحله تقسیم کرد و مورفولوژی شکستگی منطقه بهبودی ترشح را می توان به پنج مرحله تقسیم کرد. در مرحله شفا اولیه، شکستگی شکستگی شکسته یا کمی کوچک را نشان می دهد. حالت شکست نهایی شکستگی مختلط و شکستگی تقسیم شده است. ریزساختارهای خوب دانه باعث افزایش مقاومت کششی نهایی منطقه شفا خوردگی می شود که حتی بالاتر از ماتریس است. میزان بازیابی استحکام بالاتر از پلاستیک است.
موضوعات مرتبط
مهندسی و علوم پایه مهندسی مواد دانش مواد (عمومی)
چکیده انگلیسی
The behavior of internal crack healing in a low carbon steel at elevated temperatures was investigated. The internal cracks were introduced into low carbon steel samples via the drilling and compression method. The microstructure of crack healing zone was observed using optical microscopy and scanning electron microscopy. The mechanical properties of crack healing zone at room temperature were tested. The results show that there are two mechanisms of crack healing in the low carbon steel. Crack healing is caused by atomic diffusion at lower temperatures, and mainly depends on recrystallization and grain growth at higher temperatures. The microstructural evolution of crack healing zone can be divided into four stages, and the fracture morphology of crack healing zone can be classified into five stages. At the initial healing stage, the fracture exhibits brittle or low ductile dimple fracture. The ultimate fracture mode is dimple and quasi-cleavage mixed fracture. Fine grain microstructures improve the ultimate tensile strength of crack healing zone, which is even higher than that of the matrix. The strength recovery rate is higher than that of the plasticity.
ناشر
Database: Elsevier - ScienceDirect (ساینس دایرکت)
Journal: Materials Science and Engineering: A - Volume 662, 26 April 2016, Pages 65-71
نویسندگان
, , ,