کد مقاله | کد نشریه | سال انتشار | مقاله انگلیسی | نسخه تمام متن |
---|---|---|---|---|
4980343 | 1367826 | 2017 | 15 صفحه PDF | دانلود رایگان |
عنوان انگلیسی مقاله ISI
Measurement of electrostatic charging during pneumatic conveying of powders
ترجمه فارسی عنوان
اندازه گیری شارژ الکترواستاتیک در هنگام انتقال پنوماتیک از پودر
دانلود مقاله + سفارش ترجمه
دانلود مقاله ISI انگلیسی
رایگان برای ایرانیان
کلمات کلیدی
الکترواستاتیک، شارژ سه بعدی الکتریکی، مخلوط جامد سیال، دست زدن به پودر، جریان ذرات،
ترجمه چکیده
انباشت الکتریسیته ساکن در حین انتقال پودر یک منبع اشتعال احتمالی برای انفجار است و به همین علت برای ایمنی عملیات در صنعت فرآیند خطر است. با این حال، با توجه به حساسیت بالای آن به شرایط ابتدایی و مرزی، فرایند افزایش شارژ به لحاظ آزمایشی به چالش کشیده می شود و بسیاری از مکانیزم های پایه هنوز کاملا درک نشده اند. هدف این پل شکافتن، در این مقاله نتایجی از تحقیقات تجربی ما در مورد تاثیر تعدادی از پارامترها بر شارژ سه بعدی الکتریکی پودرها و لوله های حمل و نقل ارائه شده است. آزمایش ها در یک آزمایشگاه اخیرا مونتاژ شده بود که شرایط کنترل محیط را تا حد زیادی کنترل می کرد. با توجه به اندازه گیری های ما، اگر سرعت هوای انتقال افزایش یابد، میزان پودر افزایش می یابد. با این حال، با یک سرعت مشخص، پودر حداکثر بار را تجربه می کند در حالیکه برای سرعت های بالاتر هزینه ها پس از آن کاهش می یابد. سرعت هوا که میزان پودر را به حداکثر می رساند بستگی به مواد لوله، قطر و بارگیری پودر دارد. علاوه بر این، یک قطر لوله بزرگتر نشان داد که به طور قابل توجهی باعث افزایش روند شارژ می شود. نتایج بسیار قابل تکرار و در مقایسه با پیش بینی های نظری بود.
موضوعات مرتبط
مهندسی و علوم پایه
مهندسی شیمی
بهداشت و امنیت شیمی
چکیده انگلیسی
The accumulation of static electricity during powder transport is a possible ignition source for explosions and, thus, a hazard for operation safety in process industry. However, due to its high sensitivity to initial and boundary conditions, the process of charge build-up is challenging to study experimentally and many of the underlying mechanisms are still not well understood. Aiming at bridging this gap, in this paper we present the results of our experimental study on the influence of a range of parameters on the triboelectric charging of powders and transport pipes. The experiments were conducted in a recently assembled test-rig that facilitates the control of the ambient conditions to a high degree. According to our measurements, the powder charge increases if the conveying air velocity is increased. However, at a certain velocity the powder experiences a maximum charge whereas for higher velocities the charge subsequently drops. The air velocity that maximized the powder charge depends on the pipe material, diameter and powder loading. Further, a larger pipe diameter showed to enhance the charging process significantly. The results were highly repeatable and in good comparison with theoretical predictions.
ناشر
Database: Elsevier - ScienceDirect (ساینس دایرکت)
Journal: Journal of Loss Prevention in the Process Industries - Volume 49, Part B, September 2017, Pages 461-471
Journal: Journal of Loss Prevention in the Process Industries - Volume 49, Part B, September 2017, Pages 461-471
نویسندگان
N. Schwindt, U. von Pidoll, D. Markus, U. Klausmeyer, M.V. Papalexandris, H. Grosshans,