کد مقاله کد نشریه سال انتشار مقاله انگلیسی نسخه تمام متن
7974926 1514669 2016 10 صفحه PDF دانلود رایگان
عنوان انگلیسی مقاله ISI
A stress-based fracture criteria validated on mixed microstructures of ferrite and bainite over a range of stress triaxialities
ترجمه فارسی عنوان
معیارهای شکست شکستگی مبتنی بر استحکام بر روی میکروساختارهای مخلوط فریت و باینیت بر روی طیف وسیعی از ترشحات استرس
ترجمه چکیده
مهر زنی داغ یک فرایند متوالی برای تشکیل و گرمای درمان اجزای فلز ورق با خواص مکانیکی برتر است. با استفاده از نرخ خنک کننده متفاوت، ترکیب میکرو سازنده و در نتیجه خواص مواد فولادی می تواند طراحی شود. با کنترل میزان خنک کننده در بخش های مختلف خالی، خواص مواد را می توان بسته به سختی مطلوب مورد نظر طراحی کرد. تحت خنک کننده مداوم، بسته های مختلف فرایند فریت و باینیت بسته به میزان خنک کننده شکل می گیرد. این مقاله بر رفتار شکست کیکی ورقه فلزی نازک ساخته شده از فولاد ضد زنگ آلیاژ بور با مقادیر مختلف فریت و باینیت تمرکز می کند. برای ساخت ریزساختار با کسر حجمی مختلف فریت و باینیت، یک راه آزمایشی به کار برده شد. در مجموع، پنج هندسه نمونه های مختلف آزمون، نشان دهنده تنش های مختلف تنش، با حرارت تحت درمان و کشش آزمایش شدند. از طریق اندازه گیری های کامل میدان، منحنی های جریان بیش از غلظت و پلاسمای معادل آن برای شکستگی تعیین شد. نتایج تجربی بیشتر با استفاده از یک طرح همگن سازی متوسط ​​میانی همراه با معیارهای شکست شکست محلی مورد بررسی قرار گرفتند. طرح همگن سازی میدان متوسط ​​شامل تاثیر ترکیب ترکیب ریزش و سه گانه استرس با دقت قابل استفاده است، که به احتمال زیاد برای مدل سازمانی مولفه های گرم مهر و موم شده است.
موضوعات مرتبط
مهندسی و علوم پایه مهندسی مواد دانش مواد (عمومی)
چکیده انگلیسی
Hot stamping is a sequential process for formation and heat-treatment of sheet metal components with superior mechanical properties. By applying different cooling rates, the microstructural composition and thus the material properties of steel can be designed. By controlling the cooling rate in different sections of a blank, the material properties can be tailored depending on the desired toughness. Under continuous cooling, various volume fractions of ferrite and bainite are formed depending on the rate of cooling. This paper focuses on the ductile fracture behavior of a thin sheet metal made of low-alloyed boron steel with varying amounts of ferrite and bainite. An experimental setup was applied in order to produce microstructures with different volume fractions of ferrite and bainite. In total, five different test specimen geometries, representing different stress triaxialities, were heat treated and tensile tested. Through full-field measurements, flow curves extending beyond necking and the equivalent plastic strain to fracture were determined. Experimental results were further investigated using a mean-field homogenization scheme combined with local fracture criteria. The mean-field homogenization scheme comprises the influence of microstructure composition and stress triaxiality with usable accuracy, connoting auspicious possibilities for constitutive modeling of hot-stamped components.
ناشر
Database: Elsevier - ScienceDirect (ساینس دایرکت)
Journal: Materials Science and Engineering: A - Volume 674, 30 September 2016, Pages 232-241
نویسندگان
, , ,