کد مقاله کد نشریه سال انتشار مقاله انگلیسی نسخه تمام متن
4991234 1457104 2017 29 صفحه PDF دانلود رایگان
عنوان انگلیسی مقاله ISI
High-temperature analogy experimental investigation on dry granulating characteristic of rotating disk for waste heat utilization of molten slag
ترجمه فارسی عنوان
آزمایشات تجربی با درجه حرارت بالا در خصوص گرانودی خشک دیسک چرخشی برای استفاده از حرارت سریع سرباره مذاب
کلمات کلیدی
ترجمه چکیده
فرآیند گرانشی خشک یکی از روشهای امیدبخش برای استفاده از سرباره مذاب است. بازده بهبود گرما خالص و هزینه های بازیافت ذرات سرباره عمدتا تحت تاثیر ویژگی های دانه بندی قرار می گیرند. این مقاله با استفاده از چرخش دیسک با آلومینیوم مذاب به عنوان یک محیط آزمایشی با روش دمایی درجه حرارت انجام شد. نتایج نشان داد که میانگین ذرات ذرات با افزایش سرعت تغذیه و میزان خنک کردن هوا با کاهش سرعت چرخش افزایش می یابد. میزان هوای خنک کننده اثر کمی بر توزیع اندازه ذرات اصلی نشان داد، در حالی که عملکرد تولید را کاهش داد. ضریب شکل دایره ای ذرات به طور عمده تحت تاثیر سرعت چرخش، میزان هوای خنک کننده و فیلم اکسید روی سطح ذرات قرار داشت. حالت فروپاشی مایع فیلم و میزان خنک سازی ذرات نقش مهمی در تشکیل رشته ها داشتند. در حالت کاملا رباطی، کسر جرمی پایین رشته ها تولید شد، در حالی که رشته ها به سرعت افزایش می یابند، زمانی که فیلم مایع به وسیله ورقه ورق شکسته شد. در دانه بندی سرباره کوره انفجاری پیشنهاد شده است که خصوصیات ذرات باید به طور مستقیم با سرعت چرخشی کنترل شود و میزان هوای خنک کننده باید به شدت کنترل شود.
موضوعات مرتبط
مهندسی و علوم پایه مهندسی شیمی جریان سیال و فرایندهای انتقال
چکیده انگلیسی
Dry granulation process is one of the most promising methods for waste heat utilizing from molten slag. The net heat recovery efficiency and recycling costs of slag particles are mainly governed by the granulating characteristic. This paper performed a high-temperature analogy experiment by rotating disk with molten aluminum as the medium. The results indicated that the mean size of particles grew with the increasing of feed rate and cooling air rate, decreasing in rotating speed. The cooling air rate showed a little effect on the size distribution of the main particles, while lowered the production yield. The circularity shape factor of particles was mainly influenced by the rotating speed, cooling air rate and the oxide film formed on the particle surface. The liquid film breakup mode and cooling rate of particles played significant roles in the formation of filaments. In the fully-ligament mode, lower mass fraction of filaments was generated, while the filaments increased rapidly once the liquid film broke up by sheet mode. It was suggested in the granulation of blast furnace slag that, the particle characteristics should directly be governed by rotating speed, and the cooling air rate must be controlled strictly.
ناشر
Database: Elsevier - ScienceDirect (ساینس دایرکت)
Journal: Applied Thermal Engineering - Volume 125, October 2017, Pages 846-855
نویسندگان
, , , , ,