کد مقاله کد نشریه سال انتشار مقاله انگلیسی نسخه تمام متن
6748875 1430222 2015 15 صفحه PDF دانلود رایگان
عنوان انگلیسی مقاله ISI
Hygro-elasto-plastic model for planar orthotropic material
ترجمه فارسی عنوان
مدل پلاستیکی هیدرو الاستوپلاستیکی برای مواد ورقه ای
ترجمه چکیده
در این مقاله یک مدل مواد الاستوپلاستیک پلاستیکی در داخل هواپیما و یک مدل انقباض هیدرواستاتیکی برای کاغذ و هیئت مدیره معرفی شده است. پارامترهای ورودی برای هر دو مدل، انحصارطلبی جهت گیری فیبر و محتوای خشک جامدات هستند. این دو مدل براساس نتایج آزمایشگاهی می تواند در یک رویکرد تحلیلی برای برآورد، به عنوان مثال، کشش پلاستیک و انقباض در موارد یک بعدی یکپارچه، اما برای مطالعات اثرات ترکیبی و پیچیده تر رفتار رفتار انعطاف پذیر یک مدل عنصر محدود عددی ساخته شد. رویکرد عنصر محدود همچنین امکان مطالعه تغییرات ساختاری مختلف ورق ارتوپروپیک و همچنین رفتار لرزشی و شرایط تنش داخلی تحت اختلاف فشارهای محلی را فراهم کرد. چند نمونه از اثر ناهمسانگردی و رطوبت در شرایط کشش و خشک شدن بر روی اختلاف فشار و خم شدن نشان داده شده است. تنش های داخلی از طریق یک مورد مورد بررسی قرار گرفت که در آن خشک شدن لایه های مختلف در مراحل مختلف رخ داده است. هر دو رگه های ناهمسانگردی و رطوبت، قادر بودند تا لرزش نمونه قابل مشاهده باشد. پایداری این نقصها به چندین مرحله فرآیند و شرایط تنش ورق بستگی دارد، همانطور که در این مقاله نشان داده شده است. امکان استفاده از مدل پلاستیکی الاستیسیته پلاستیکی متنوع است، از جمله بررسی پدیده های مختلف و نقص هایی که در خشک کردن، تبدیل و چاپ شرایط تولید وجود دارد.
موضوعات مرتبط
مهندسی و علوم پایه سایر رشته های مهندسی مهندسی عمران و سازه
چکیده انگلیسی
An in-plane elasto-plastic material model and a hygroexpansivity-shrinkage model for paper and board are introduced in this paper. The input parameters for both models are fiber orientation anisotropy and dry solids content. These two models, based on experimental results, could be used in an analytical approach to estimate, for example, plastic strain and shrinkage in simple one-dimensional cases, but for studies of the combined and more complicated effects of hygro-elasto-plastic behavior, a numerical finite element model was constructed. The finite element approach also offered possibilities for studying different structural variations of an orthotropic sheet as well as buckling behavior and internal stress situations under local strain differences. A few examples are presented of the effect of the anisotropy and moisture streaks under stretching and drying conditions on strain differences and buckling. The internal stresses were studied through a case in which the drying of different layers occurred at different stages. Both the anisotropy and moisture streaks were capable of rendering the buckling of the sample visible. The permanency of these defects highly depends on several process stages and tension conditions of the sheet, as demonstrated in this paper. The application possibilities of the hygro-elasto-plastic model are diverse, including investigation into several phenomena and defects appearing in drying, converting and printing process conditions.
ناشر
Database: Elsevier - ScienceDirect (ساینس دایرکت)
Journal: International Journal of Solids and Structures - Volume 62, 1 June 2015, Pages 66-80
نویسندگان
, , , ,