کد مقاله کد نشریه سال انتشار مقاله انگلیسی نسخه تمام متن
7008063 1455265 2018 11 صفحه PDF دانلود رایگان
عنوان انگلیسی مقاله ISI
Design of electrodialysis desalination plants by considering dimensionless groups and variable equivalent conductivity
ترجمه فارسی عنوان
طراحی گیاهان آب شیرین کننده الکترودیلیز با استفاده از گروه های بدون بعد و هدایت معادل متغیر
ترجمه چکیده
گیاهان شیرین کننده الکترویدیالیز برای آب شور، بر اساس پارامترهای مختلف مانند غلظت خوراک، تراکم جریان و ساخت پشته طراحی شده اند. از جمله فرضیه های مختلف مدل، ثابت بودن هدایت معادل جریان رقیق شده و کنسانتره، یکی از مهمترین آنهاست. در این مقاله، این فرض در سطوح مختلف آرام است و برای رسیدن به اثرات آن، راه حل های بسته به دست آمده است. نشان داده شده است که نتایج قبلا منتشر شده می تواند تکرار شود. همچنین مقایسه بین مدل توزیع شده و تحقیق نشان میدهد که استفاده از نرخ جریان ورودی در مدل توزیع به جای سرعت تولید محصول، نتایج دقیقتری را ارائه میدهد. تجزیه و تحلیل بیشتر نشان می دهد یک عدد بی عیب، نامیده می شود تعداد الکترو دیالایتی بیوت، که نسبت کل حجم به غلظت خروج بر اساس میانگین مقاومت سلولی سلول. به نظر جرمی برابر با تعداد پشته ها بود. این یک معیار روشن برای اینکه چه زمانی باید مدل توزیع مورد استفاده قرار گیرد، فراهم کرد. به طور خاص، تا زمانی که تعداد بیوت الکترودیتالیتی (کمتر از یا) برابر با 1 باشد، باید مدل توزیع شده استفاده شود، در غیر این صورت مدل مرحله ای انتخاب مناسب تر است. این همچنین جهت تحقیقات آینده را فراهم می کند. نمودار طراحی نیز برای تسهیل روش محاسبات توسعه یافته است.
موضوعات مرتبط
مهندسی و علوم پایه مهندسی شیمی تصفیه و جداسازی
چکیده انگلیسی
Electrodialysis desalination plants, for brackish water, are designed based on different parameters such as feed concentration, current density, and stack construction. Among the various model assumptions, the constancy of the equivalent conductivity of the diluate and concentrate streams is considered a prominent one. In this paper, this assumption is relaxed at different levels and closed-form solutions are obtained to ascertain its effects. It is shown that previously published results can be replicated. Also, a comparison between the lumped and staged model shows that using the inlet flow rate in the lumped model instead of the product flow rate provides more accurate results. Further analysis reveals a non-dimensional number, termed the electrodialytic Biot number, which is the ratio of the total to exit concentration based average cell pair volume resistance. It was found to be physically equivalent to the number of stacks. This provided a clear criterion as to when the lumped model should be used. Specifically, as long as the electrodialytic Biot number is (less than or) equal to 1, the lumped model should be used, otherwise the staged model is a more appropriate choice. It also provides direction for future research. A design chart is also developed to facilitate the calculation procedure.
ناشر
Database: Elsevier - ScienceDirect (ساینس دایرکت)
Journal: Desalination - Volume 430, 15 March 2018, Pages 197-207
نویسندگان
, ,