Keywords: چرخش دنده ها; Spur gears; Oil injection methods; Lubrication; Influence mechanism;
مقالات ISI چرخش دنده ها (ترجمه نشده)
مقالات زیر هنوز به فارسی ترجمه نشده اند.
در صورتی که به ترجمه آماده هر یک از مقالات زیر نیاز داشته باشید، می توانید سفارش دهید تا مترجمان با تجربه این مجموعه در اسرع وقت آن را برای شما ترجمه نمایند.
در صورتی که به ترجمه آماده هر یک از مقالات زیر نیاز داشته باشید، می توانید سفارش دهید تا مترجمان با تجربه این مجموعه در اسرع وقت آن را برای شما ترجمه نمایند.
Keywords: چرخش دنده ها; Spur gears; Face load factor; Load distribution; Finite element method; Beam elements; Nonlinear stiffness;
Keywords: چرخش دنده ها; Spur gears; Mesh stiffness; Load sharing ratio; Fillet foundation stiffness; The minimum potential energy principle;
Keywords: چرخش دنده ها; Spur gears; Mesh stiffness; Gear body-induced tooth deflections; Fillet foundation stiffness; Analytical formulas;
Keywords: چرخش دنده ها; Spur gears; Meshing stiffness; Load distribution; Load capacity;
Keywords: چرخش دنده ها; Spur gears; Addendum; Dedendum; Cutter tip radius; Tooth thickness; Pressure angle; Interference; Corner contact; Tooth pointing; Undercutting; Non-standard; Non-dimensional; Design guideline;
Keywords: چرخش دنده ها; EHL; elastohydrodynamic lubrication; HPSTC; highest point of single tooth contact along the line of action; LOA; line of action; LPSTC; lowest point of single tooth contact along the line of action; Starved lubrication; Spur gears; Film thickness; Frictio
Keywords: چرخش دنده ها; Mathematical phenomenology; Non-linear dynamics; Oscillatory motion; Variable stiffness; Spur gears; Radial ball bearings
Keywords: چرخش دنده ها; Spur gears; Line of action (LoA); Mixed elastohydrodynamic lubrication (EHL); Surface roughness; Wear;
Gear tooth mesh stiffness: A comparison of calculation approaches
Keywords: چرخش دنده ها; Tooth mesh stiffness; Spur gears; Gear tooth modifications; Finite element/contact mechanics; Gear vibration;
Effects of misalignment error, tooth modifications and transmitted torque on tooth engagements of a pair of spur gears
Keywords: چرخش دنده ها; Spur gears; Assembly errors; Tooth modifications; Mesh stiffness; Load-sharing ratios; Contact stresses
Detection and diagnosis of surface wear failure in a spur geared system using EEMD based vibration signalanalysis
Keywords: چرخش دنده ها; Spur gears; Lubricant film thickness; Empirical mode decomposition; Kurtosis values
Influence of real surface topography on the contact area ratio in differently manufactured spur gears
Keywords: چرخش دنده ها; Surface topography; Contact mechanics; Spur gears; Finishing
Effect of lubricant selection on EHL performance of involute spur gears
Keywords: چرخش دنده ها; EHL; Rheology; Spur gears; Scuffing;
Thermal elastohydrodynamic simulation of involute spur gears incorporating mixed friction
Keywords: چرخش دنده ها; Spur gears; Transient thermal elastohydrodynamics; Surface roughness; Three-dimensional contact;
Analysis of nonlinear oscillations in spur gear pairs with approximated modelling of backlash nonlinearity
Keywords: چرخش دنده ها; Spur gears; Backlash; Nonlinear oscillations; Transmission error; Jumps; Stability
Influence of the addendum modification on spur gear efficiency
Keywords: چرخش دنده ها; Spur gears; Power loss; Friction; Addendum modifications; Gear optimization
Computer vision algorithms for measurement and inspection of spur gears
Keywords: چرخش دنده ها; Spur gears; Computer vision; Image processing; Measurements
Undercutting and contact characteristics of longitudinal cycloidal spur gears generated by the dual face-hobbing method
Keywords: چرخش دنده ها; Spur gears; Face-hobbing method; Cycloidal; Tooth undercutting; Tooth contact analysis
Surface initiated tooth flank damage. Part II: Prediction of micropitting initiation and mass loss
Keywords: چرخش دنده ها; Spur gears; Gear micropitting; Mixed film lubrication; Fatigue crack initiation; Dang Van fatigue criterion
Surface initiated tooth flank damage: Part I: Numerical model
Keywords: چرخش دنده ها; Spur gears; Gear micropitting; Mixed film lubrication; Fatigue crack initiation; Dang Van fatigue criterion
Test rig for micro gear and experimental analysis on the meshing condition and failure characteristics of steel micro involute gear and metallic glass one
Keywords: چرخش دنده ها; Gears (general); Micro gears; Spur gears
Reduction of gear fillet stresses by using one-sided involute asymmetric teeth
Keywords: چرخش دنده ها; Spur gears; Asymmetric teeth; Circular fillet; Root stress; FEA
A dual face-hobbing method for the cycloidal crowning of spur gears
Keywords: چرخش دنده ها; Spur gears; Face-hobbing method; Cycloidal