کد مقاله کد نشریه سال انتشار مقاله انگلیسی نسخه تمام متن
7058495 1458078 2013 10 صفحه PDF دانلود رایگان
عنوان انگلیسی مقاله ISI
Filling dynamics and phase change of molten salt in cold receiver pipe during initial pumping process
ترجمه فارسی عنوان
پویایی پرکننده و تغییر فاز نمک مذاب در لوله گیرنده سرد در طی فرآیند پمپاژ اولیه
کلمات کلیدی
نمک مذاب، فرآیند پمپاژ اولیه، پویایی پر کردن، تغییر فاز، حجم مدل مایع
ترجمه چکیده
دینامیک پر شدن و تغییر فاز نمک مذاب در لوله گیرنده سرد در طی فرآیند پمپاژ اولیه با استفاده از منحنی مشخصه پمپ، با سرعت متغیر ورودی مورد تجزیه و تحلیل قرار گرفته است. به طور کلی، لوله گیرنده سرد در طی فرآیند پمپاژ اولیه برای خنک شدن مذاب مذاب، به عنوان دمای ورودی پایین تر از دمای بحرانی یخ زده است، یا در غیر این صورت با فرآیند ذوب شدن در دمای ورودی بالاتر، امکان پذیر نخواهد بود. در طی فرایند پمپاژ با ذوب، سرعت جریان ابتدا با خنک شدن کاهش می یابد و سپس با اثر ذوب افزایش می یابد و زمان ذوب با دمای ورودی کاهش می یابد. همانطور که پدیده یخبندان در جریان پمپاژ ظاهر می شود، سرعت جریان به صفر کاهش می یابد، در حالی که افت فشار به حداکثر فشار می رسد و زمان انجماد با دمای ورودی افزایش می یابد. از آنجایی که یک لایه جامد در مجاورت منطقه فاز مجاور دیواره لوله وجود دارد، سرعت جریان و افت فشار در جهت جریان افزایش قابل توجهی افزایش می یابد و منطقه تغییر فاز به افت فشار تبدیل می شود. همانطور که دمای ورودی کاهش می یابد، منطقه تغییر فاز به طور قابل توجهی افزایش می یابد و زمان پر شدن افزایش می یابد.
موضوعات مرتبط
مهندسی و علوم پایه مهندسی شیمی جریان سیال و فرایندهای انتقال
چکیده انگلیسی
The filling dynamics and phase change performances of molten salt in cold receiver pipe during initial pumping process are numerically analyzed with variable inlet velocity due to pump characteristic curve. In general, cold receiver pipe during initial pumping process will be frozen for molten salt solidification as the inlet temperature is lower than critical temperature, or else it will be unobstructed with melting process at higher inlet temperature. During pumping process with melting, the flow velocity will first decrease by solidification and then increase by melting effect, and the melting time decreases with inlet temperature. As the freezing phenomena appears during pumping process, the flow velocity will decrease to zero, while the pressure loss reaches the maximum pressure head, and the freezing time increases with inlet temperature. Since a solid layer exists adjacent to the pipe wall in phase change region, the flow velocity and pressure loss remarkably increases along flow direction, and the phase change region will dominate the pressure loss. As the inlet temperature decreases, the phase change region remarkably enlarges, and the filling time rises.
ناشر
Database: Elsevier - ScienceDirect (ساینس دایرکت)
Journal: International Journal of Heat and Mass Transfer - Volume 64, September 2013, Pages 98-107
نویسندگان
, , ,