کد مقاله کد نشریه سال انتشار مقاله انگلیسی نسخه تمام متن
4929222 1432276 2017 13 صفحه PDF دانلود رایگان
عنوان انگلیسی مقاله ISI
Compression-shear behavior of a scaled immersion joint with steel shear keys
ترجمه فارسی عنوان
رفتار فشاری-برشی یک مفصل غوطه ور مقیاس با کلید های برش فولادی
کلمات کلیدی
تونل غوطه ور مفصلی غوطه ور، کلید برش فولادی، سختی برشی، ظرفیت برش، شکست برش،
ترجمه چکیده
رفتار برش یک جسم غوطه وری تحت بارهای فشاری برشی در این مقاله مورد بررسی قرار گرفته است. برای بررسی عملکرد مشترک غوطه وری، یک نمونه مقیاس شده، بر اساس یک پروتکل خاص یک پروژه واقعی طراحی شده است. یک نیروی برشی شبه استاتیک به صورت افقی اعمال می شود در حالی که یک نیروی فشاری ثابت بر روی مفصل نگه داشته می شود. اثر هیسترزیس در طول آزمایش مشاهده می شود و سطح حلقه هیسترتیک با نیروی برشی افزایش می یابد. منحنی پاکتی از نیروی برشی جابجایی مفصل بدست می آید و بر اساس رفتار برشی مشاهده شده از مفصل به چهار مرحله تقسیم می شود. استحکام برشی مفصل غوطه وری محاسبه می شود، نشان دهنده تغییر غیر خطی با جابه جایی برشی است. ظرفیت برش مدل مشترک غوطه وری و کلید برش فولادی تنها مورد بررسی قرار می گیرد. مشخص شده است که ظرفیت مشترک کمتر از مجموع ظرفیت کلیه کلیدهای برشی است. این نشان می دهد که کلیدهای برش در همان زمان فعال نیستند. حالت شکست در مفصل شامل یک شکست برشی شکننده در کلیدهای برشی تنها و یک روش گام به گام شکست کامل اتصال است.
موضوعات مرتبط
مهندسی و علوم پایه علوم زمین و سیارات مهندسی ژئوتکنیک و زمین شناسی مهندسی
چکیده انگلیسی
The shear behavior of an immersion joint subjected to compressive-shear loads is investigated in this paper. To explore the performance of the immersion joint a scaled specimen, according to a specific protocol of a real project, is designed. A quasi-static shear force is applied horizontally while a constant compression force is maintained on the joint. A hysteresis effect is observed during the test and the area of the hysteretic loop increases with the shear force. An envelope curve of the shear force-displacement of the joint is obtained and divided into four stages based on the observed shear behavior of the joint. The shear stiffness of the immersion joint is calculated, showing a non-linear change with the shear displacement. The shear capacity of the model immersion joint and that of a single steel shear key are evaluated. It is found that the capacity of the joint is smaller than the sum of the capacities of all shear keys. This shows that the shear keys are not activated at the same time. The failure mode of the joint consists of a brittle shear failure in the single shear keys and a step-by-step failure way of the complete joint.
ناشر
Database: Elsevier - ScienceDirect (ساینس دایرکت)
Journal: Tunnelling and Underground Space Technology - Volume 70, November 2017, Pages 76-88
نویسندگان
, , , , ,